Boss-audio-systems GS-10 Bedienungsanleitung

Owner’s Manual 03342912 ‘03-8-1N Thank you, and congratulations on your choice of the BOSS GS-10 Guitar Effects System with USB Audio Interf

10Panel DescriptionsFront Panelfig.00-0411. DisplayA variety of information about the GS-10 appears here. Normally, patch names are displayed.2. PREAM

100Appendices03 01 00 6E 00 00 00 01 00 - 32 User 1 F# Step1503 01 00 6F 00 00 00 01 00 - 32 User 1 F# Step1603 01 00

101AppendicesAppendicesTable AR Step Note <AUTO RIFF User Phrase>---------------- ----------------Data(H) Descriptio

102AppendicesTable AMP <AMP Customize>--------------------------------------------------------------------------------------------

103AppendicesAppendicesTable OD/DS <OD/DS Customize>--------------------------------------------------------------------------------

104AppendicesTable Quick Fx Data <Quick Fx Data>--------------------------------------------------------------------------------------------

105AppendicesAppendices--- COMP ---** ** 01 00 00 00 00 02 00 - 64 CS :Sustain** ** 01 02 00 00 00 02 00 - 64 CS :Leve

106Appendices 00 00 00 02 00 - 64 AR :Sensitivity 00 00 00 02 00 - 02 SYN:Octave Shift *R

107AppendicesAppendices 00 00 00 02 00 - 64 SYN:FLT.Decay BS :---

108Appendices 00 00 00 02 00 - 64 SYN:Synth Level BS :---

109AppendicesAppendices--- FX-2 ---** ** 05 00 00 00 00 01 20 - 7F Name 1 *Refer to "Table Name"** ** 05 01# 00

11Panel DescriptionsTAP ButtonUse this when setting the delay time with the tap input. (p. 33)6. CHORUS (p. 21, p. 34)LEVEL KnobAdjusts the volume lev

110Appendices 01 : Rack 160D

111AppendicesAppendices** ** 03 18 00 00 00 01 00 - 01 PRE/SP:Bright (Bch)** ** 03 19 00 00 00 01 00 - 02 PR

112Appendices** ** 05 2B 00 00 00 01 00 - 64 PS :PS2 Level 0 - 100** ** 05 2C 00 00 00 01 00 - 64 PS :Direct

113AppendicesAppendices** ** 06 00 00 00 00 01 00 - 28 SEQ:High EQ -20dB - +20dB** ** 06 01 00 00 00 01 00 - 28

114Appendices--- ASSIGN 2 ---** ** 0F 00 00 00 00 01 00 - 01 ASSIGN 2:On/Off 00 : Off

115AppendicesAppendicesTable Patch Change <Patch Change>-----------------------------------------------------------------------------------

116AppendicesTable Quick Fx Target <Quick Fx: Assign Target>---------------- ----------------Data(H) Description-------

117AppendicesAppendices00 00 0E 01 CE :Mode00 00 0E 02 CE :Rate00 00 0E 03 CE :Depth00 00 0E 04 CE :Pr

118AppendicesTable EQ Middle Frequency <EQ(SEQ): Lo(Hi)-Mid f>---------------- ----------------Data(H) Description-

119AppendicesAppendicesTable HR Scale <Harmony Scale>---------------------------------------------Table OC Range <OC: Range

12Panel DescriptionsRear Panelfig.00-0421. MIC INPUT Jack/ConnectorInput jack/connector for use with mics. Both standard TRS type and XLR type are pro

120AppendicesTable Chain <Effect Chain>---------------- ----------------Data(H) Description----------------

121AppendicesAppendices00 6E HR :HR1 Harmony00 6F HR :HR1 Pre Delay00 70 HR :HR1 Feedback00 71

122AppendicesMIDI Implementation ChartFunction...BasicChannelModeNoteNumber :VelocityAfterTouchPitch BendControlChangeProgChangeSystem ExclusiveSystem

123AppendicesAppendicesSpecificationsGS-10: Guitar Effects System with USB Audio InterfaceRated Power Output1.5 W + 1.5 WSignal ProcessingAD Conversio

124AppendicesFX-1 buttonFX-2 buttonEQ buttonNAME/NS/MASTER buttonASSIGN buttonINPUT SELECT buttonQUICK FX buttonPARAMETER button L/REXIT buttonWRITE b

125Installing & Setup the USB DriverIn order to use the GS-10 USB, you must first install the USB driver. The USB Driver is included in the “GS-10

126Installing & Setting Up the Driver (Windows)Special Driver and Standard DriverThe GS-10 features two operational modes, each of which uses a di

127Installing & Setting Up the Driver (Windows)Installing the special driver Windows XP/2000 usersWindows XP1.With the GS-10 disconnected, start

128Installing & Setting Up the Driver (Windows)9.In the dialog box that appears, input the following into the “Open” field, and click [OK].D:\DRIV

129Installing & Setting Up the Driver (Windows)fig.11-06014.Select “Don’t search. I will choose the driver to install”, and click [Next].fig.11-07

13Panel DescriptionsSignal Flowfig.00-043MIDI OUTMIDI INCONTROL OUTCONTROL INGS-10 OUTGS-10 INCONTROLMULTI EFFECTSA/D D/AUSBINPUTSELECTMIDISELECTCompu

130Installing & Setting Up the Driver (Windows)17.Input the following into the “Copy files from” field, and click [OK].D:\DRIVER\USB_XP2k* The dri

131Installing & Setting Up the Driver (Windows)Windows 20001.With the GS-10 disconnected, start up Windows.Disconnect all USB cables except for a

132Installing & Setting Up the Driver (Windows)9.In the dialog box that appears, input the following into the “Open” field, and click [OK].D:\DRIV

133Installing & Setting Up the Driver (Windows)fig.11-18013.Click [OK].The “Files Needed” dialog box will appear.14.In the Copy files from field,

134Installing & Setting Up the Driver (Windows)15.Verify that “BOSS GS-10” is displayed, and click [Finish].Driver installation will begin.When dr

135Installing & Setting Up the Driver (Windows) Windows Me/98 users1.With the GS-10 disconnected, start up Windows.Disconnect all USB cables exce

136Installing & Setting Up the Driver (Windows)Installing the OS-standard driver Windows XP/2000 users1.With the GS-10 disconnected, start up Win

137Installing & Setting Up the Driver (Windows) Windows Me users1.With the GS-10 disconnected, start up Windows.Disconnect all USB cables except

138Installing & Setting Up the Driver (Windows) Windows 98 usersThe USB composite device driver is installed first, then the USB audio device dri

139Installing & Setting Up the Driver (Windows)8.Check CD-ROM drive, and click [Next].A dialog box like the one shown below will appear.fig.11-310

14Chapter 1 Playing SoundsMaking the Connectionsfig.01-010* To prevent malfunction and/or damage to speakers or other devices, always turn down the vo

140Installing & Setting Up the Driver (Windows)11.Click [Next], and proceed with the installation in the same way as in steps 8–10.When installati

141Installing & Setting Up the Driver (Windows)Driver settings About the input/output devicesAudio output devicesBOSS GS-10This sends audio data

142Installing & Setting Up the Driver (Windows) Specifying the audio input/output destinationWindows XP/2000/Me users1.Open Control Panel.Windows

143Installing & Setting Up the Driver (Windows)Windows 98 users1.Click the Windows Start button, and from the menu that appears, select “Settings

144Installing & Setting Up the Driver (Windows) Volume Control setting1.Click the Windows Start button, and select “Programs | Accessories | Ente

145Installing & Setting Up the Driver (Windows)When playing audio CDs from the computer’s internal CD-ROM drive, or using the GS-10 to play game m

146Installing & Setting Up the Driver (Macintosh)Special Driver and Standard DriverThe GS-10 features two operational modes, each of which uses a

147Installing & Setting Up the Driver (Macintosh)Use the following procedure to install the GS-10 driver.1.Exit all currently running software (ap

148Installing & Setting Up the Driver (Macintosh)OMS settingsIf other MIDI devices are connected, you must turn off the power on all devices, and

149Installing & Setting Up the Driver (Macintosh)5.Click [Search].6.When the search has been completed, verify that the “OMS Driver Setup” dialog

15Chapter 1 Playing SoundsSection 1● When using the unit with an expression pedal connected to the EXP PEDAL/CTL 1,2 jack, set Minimum Volume to the “

150Installing & Setting Up the Driver (Macintosh)11.From the Edit menu, select “OMS MIDI Setup”. In the OMS MIDI Setup dialog box that appears, ch

151Installing & Setting Up the Driver (Macintosh)FreeMIDI settingsIf other MIDI devices are connected, you must turn off the power on all devices,

152Installing & Setting Up the Driver (Macintosh)The About Quick Setup dialog box will appear. fig.11-520* If the dialog will not appear, select “

153Installing & Setting Up the Driver (Macintosh)14.If a MIDI sound module is connected to the GS-10’s MIDI OUT connector, click the GS-10 MIDI IN

154Installing & Setting Up the Driver (Macintosh)Installing the ASIO driverYou must install the MIDI driver even if you will be using only audio o

155Installing & Setting Up the Driver (Macintosh) Mac OS X users1.With the GS-10 disconnected, start up Mac OS.Disconnect all USB cables except f

156Installing & Setting Up the Driver (Macintosh)8.Click [Continue Installation].The display will indicate “The software was successfully installe

157Installing & Setting Up the Driver (Macintosh)Installing the OS-standard driver Mac OS 9/8 users1.With the GS-10 disconnected, start up Mac OS

158Installing & Setting Up the Driver (Macintosh)Settings the sound input/output1.From the Apple menu, select “Control Panel” – “Sound.”The “Sound

159Installing & Setting Up the Driver (Macintosh)5.In “Choose a source for sound input (Device),” select “USB audio.”fig.11-670* Do not check “Pla

16Chapter 1 Playing SoundsSetting Output Device (Amps) (OUTPUT SELECT)Select the type of output device connected to the OUTPUT jack or GUITAR AMP OUT

160Installing & Setting Up the Driver (Macintosh) Mac OS X users1.With the GS-10 disconnected, start up Mac OS.Disconnect all USB cables except f

161Installing & Setting Up the Driver (Macintosh)8.In the Output tab, set “Choose a device for sound output” to “GS-10.”fig.11-7009.In the Input t

162Setting the Special Driver’s FunctionsAdjusting the audio latencyWhen using the GS-10 in Advanced mode, you can change the driver settings to adjus

163Setting the Special Driver’s FunctionsOpening the special driver settings dialog boxIf using Windows:1. Open the “Control Panel” and double-click “

164TroubleshootingIf there is no sound or other operational problems occur, first check through the following solutions. If this does not resolve the

165TroubleshootingOther ProblemsPatch does not change❏ Is something other than the Play screen shown in the display?→ On the GS-10, patches can be sel

166Troubleshooting❏ It has been found that in some cases, not all of the Windows 98 files required to support audio via USB are installed when a compu

167TroubleshootingDevice Manager shows “?”, “!”, or “USB Composite Device”The “Insert Disk” dialog box does not appear→ Use the following procedure to

168Troubleshooting❏ Are you running multiple applications?→ If multiple applications are running simultaneously, an error message may appear. If this

169TroubleshootingInterrupted notes or delays occur during MIDI playback❏ Make Windows XP settings to enable background processing.→ Make the followin

17Chapter 1 Playing SoundsSection 1Connecting Audio Devices to the AUX INPUT JackWhen using a CD or MD player, rhythm machine, or similar device for p

170Troubleshooting❏ Is the GS-10 connected to a USB hub?→ Try connecting the GS-10 directly to the USB connector of the Macintosh itself.❏ Are you usi

171Troubleshooting❏ Does your computer satisfy the requirements of the USB standard?→ If you are using a computer (such as a computer that you yoursel

172TroubleshootingDigitally recorded sound is distorted, is at the wrong pitch, or contains noise❏ Is the application's sampling frequency set to

173TroubleshootingDeleting the special driverIf you were unable to install the special driver according to the procedure given, the GS-10 may not be r

174IndexNumerics2x2 Chorus ... 45AAC Adaptor ...

175IndexKKnob Mode ... 66LLCD Contrast ...

176IndexTTAP ... 11Tone Modify ...

177MEMO

178For the USADECLARATION OF CONFORMITYCompliance Information StatementModel Name :Type of Equipment :Responsible Party :Address :Telephone :GS-10Guit

This product complies with the requirements of European Directive 89/336/EEC.For EU CountriesFor EU CountriesApparatus containing Lithium batteriesA

18Chapter 2 Creating Your Own Favorite Tones (Patches)What is a Patch?The GS-10 can store 200 combinations (or “sets”) of effects and parameter settin

Owner’s Manual 03342912 ‘03-8-1N Thank you, and congratulations on your choice of the BOSS GS-10 Guitar Effects System with USB Audio Interf

19Chapter 2 Creating Your Own Favorite Tones (Patches)Section 2Selecting the Input (INPUT SELECT)This selects the input signal to which the effects ar

This product complies with the requirements of European Directive 89/336/EEC.For EU CountriesFor EU CountriesApparatus containing Lithium batteriesA

20Chapter 2 Creating Your Own Favorite Tones (Patches)USB (Bass):You can add effects to the signals input from the USB connector (for sounds in the ba

21Chapter 2 Creating Your Own Favorite Tones (Patches)Section 2Adjusting the Tones with the KnobsThe GS-10 panel features 13 knobs for adjusting effec

22Chapter 2 Creating Your Own Favorite Tones (Patches)Turning the Effect On and OffThe GS-10’s internal effects are switched on and off with button co

23Chapter 2 Creating Your Own Favorite Tones (Patches)Section 23. Rotate the VALUE dial to select the Quick Setting you want.The tone switches to that

24Chapter 2 Creating Your Own Favorite Tones (Patches)Naming PatchesEach patch can be given a name (Patch Name) consisting of up to sixteen characters

25Section 3Chapter 3 Saving the Tones You Have CreatedStoring Patches (PATCH WRITE)When you want to keep a tone created with the Quick Settings or a t

26Chapter 3 Saving the Tones You Have CreatedExchanging PatchesOn the GS-10, you can “swap” or exchange the positions of two User patches. The followi

27Chapter 3 Saving the Tones You Have CreatedSection 3Registering Your Favorite Patches (DIRECT PATCH)You can register preferred patches to DIRECT PAT

28Chapter 4 Introduction to Effects and ParametersIn this chapter you will find detailed descriptions for each of the GS-10’s onboard effects, and the

29Chapter 4 Introduction to Effects and ParametersSection 4TypeThis sets the type of the guitar preamp.* When the type is set to CONCERT 810, SESSION,

3 013 • In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the

30Chapter 4 Introduction to Effects and ParametersWhen CUSTOM 1–3 is selected for TypeYou can set the following parameters when Type is set to CUSTOM.

31Chapter 4 Introduction to Effects and ParametersSection 4EDIT CUSTOM SP 1 –2Parameter ValueSpeaker Size 5”–15”Color Low -10–+10Color High -10–+10Spe

32Chapter 4 Introduction to Effects and ParametersOD/DS (Overdrive/Distortion)This effect distorts the sound to create long sustain. It provides 22 ty

33Chapter 4 Introduction to Effects and ParametersSection 4DELAYThis effect adds delayed sound to the direct sound, giving more body to the sound or c

34Chapter 4 Introduction to Effects and ParametersCHORUSIn this effect, a slightly detuned sound is added to the original sound to add depth and bread

35Chapter 4 Introduction to Effects and ParametersSection 4Rev Time (Reverb Time)Adjusts the length (time) of reverberation.Pre DelayAdjusts the time

36Chapter 4 Introduction to Effects and ParametersFX-1With FX-1, you can select the effect to be used from the following.• PEDAL WAH• AUTO WAH• TONE M

37Chapter 4 Introduction to Effects and ParametersSection 4ModeSelection for the wah mode.LPF (Low Pass Filter):This creates a wah effect over a wide

38Chapter 4 Introduction to Effects and ParametersACS (Advanced Compressor)This is an effect that produces a long sustain by evening out the volume le

39Chapter 4 Introduction to Effects and ParametersSection 4ENH (Enhancer)By adding sounds which are out-of-phase with the direct sound, this effect en

4 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and observe the following: Power Supply

40Chapter 4 Introduction to Effects and ParametersDF (Defretter)This simulates a fretless guitar.Parameter ValueTone -50–+50Sens 0–100Attack 0–100Dept

41Chapter 4 Introduction to Effects and ParametersSection 4Rise TimeThis determines the time needed for the volume of the feedback sound to reach its

42Chapter 4 Introduction to Effects and ParametersPH (Phaser)By adding varied-phase portions to the direct sound, the phaser effect gives a whooshing,

43Chapter 4 Introduction to Effects and ParametersSection 4ResonanceDetermines the amount of resonance (feedback). Increasing the value will emphasize

44Chapter 4 Introduction to Effects and ParametersCreating Harmonist Scales (User Scale)When “Harmony” is set to any value from -2oct to +2oct, and th

45Chapter 4 Introduction to Effects and ParametersSection 4* When set to BPM, the value of each parameter will be set according to the value of the Ma

46Chapter 4 Introduction to Effects and ParametersXover f (Crossover Frequency)This parameter sets the frequency at which the frequency components of

47Chapter 4 Introduction to Effects and ParametersSection 4DepthThis adjusts the depth of the vibrato.TriggerThis selects on/off of the vibrato.* It i

48Chapter 4 Introduction to Effects and ParametersSDD (Short Delay)This is a delay with the maximum delay time of 400 ms. This effect is useful for ma

49Chapter 4 Introduction to Effects and ParametersSection 4SL (Slicer)This consecutively interrupts the sound to create the impression that a rhythm b

5IMPORTANT NOTES 559a • When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you

50Chapter 4 Introduction to Effects and ParametersKeySelect the key of the song that you wish to play.AttackAdjust the strength of the attack. By addi

51Chapter 4 Introduction to Effects and ParametersSection 4WaveThis selects a wave type that is the source of the guitar synthesizer.Square:The unit d

52Chapter 4 Introduction to Effects and ParametersVelocityThis adjusts the amount of the volume change of the synthesizer sound. When it is set to hig

53Chapter 4 Introduction to Effects and ParametersSection 4NAME/NS/MASTERYou can select the following items in NAME/NS/MASTER.• Name (Patch Name)• Noi

54Chapter 4 Introduction to Effects and ParametersMasterParameter ValuePatch Level 0–200Master BPM 40–250Patch LevelThis adjusts the output volume of

55Section 5Chapter 5 Creating Original Effects Types (Customize)With the GS-10’s Customize function, you can rely on your own sensibilities and create

56Chapter 5 Creating Original Effects Types (Customize)Customizing the SpeakersYou can make three different sets of settings, Custom 1 and Custom 2.*

57Chapter 5 Creating Original Effects Types (Customize)Section 5TypeSelects the basic type of overdrive/distortion.BottomAdjusts the amount of distort

58Chapter 6 Setting the External Pedal FunctionsThis section describes the settings required to use an expression pedal or foot switch connected to th

59Chapter 6 Setting the External Pedal FunctionsSection 6Setting the External Foot Switch Functions (Control 1, 2 Function)* When connecting two foot

6 Contents USING THE UNIT SAFELY ...2IMPORTANT NOTES ...4 Main Features ...9 Pa

60Chapter 6 Setting the External Pedal FunctionsSetting the External Pedal Function for Individual Patches (Assign)There are two ways to set the assig

61Chapter 6 Setting the External Pedal FunctionsSection 6Manual SettingsHere, you can individually determine which controller is to control which para

62Chapter 6 Setting the External Pedal Functions* Although you can set this so that the same target is controlled by more than one controller, in such

63Chapter 6 Setting the External Pedal FunctionsSection 6Sourcefig.06-090dThis sets the controller (source) that affects the target parameter.Controll

64Chapter 7 Convenient Functions and System SettingsTuning the GuitarWhen the Tuner is turned on, sounds input to the GS-10 are output directly as is

65Chapter 7 Convenient Functions and System SettingsSection 7Bypass:Sounds input to the GS-10 bypass the processing and are output directly as is.* Th

66Chapter 7 Convenient Functions and System SettingsKeeping the Same Pedal Operations When Switching Patches (Assign Hold)This setting determines whet

67Chapter 7 Convenient Functions and System SettingsSection 7Checking the Effect Output Level with the Level MeterYou can meter the output level of ea

68Chapter 8 Using the GS-10 with External MIDI Devices ConnectedOperations Using MIDIYou can perform the following operations using MIDI with the GS-1

69Chapter 8 Using the GS-10 with External MIDI Devices ConnectedSection 8Making the Settings for MIDI FunctionsHere is a description of the GS-10’s MI

7Contents VB (Vibrato)...46UV (Uni-V) ...

70Chapter 8 Using the GS-10 with External MIDI Devices ConnectedRemote Ctrl (Remote Control)Valid Settings: Standard, Advanced, MMCThis setting determ

71Chapter 8 Using the GS-10 with External MIDI Devices ConnectedSection 8Transmitting and Receiving Settings DataOn the GS-10, you can use Exclusive m

72Chapter 8 Using the GS-10 with External MIDI Devices Connectedfig.08-180dWhen the transmission is completed, the screen prior to transmission return

73Chapter 8 Using the GS-10 with External MIDI Devices ConnectedSection 8Setting the Program Change MapWhen switching patches using Program Change mes

74Chapter 8 Using the GS-10 with External MIDI Devices ConnectedEnabling/Disabling the Program Change Map Settings (MIDI Map Select)This setting deter

75Chapter 8 Using the GS-10 with External MIDI Devices ConnectedSection 8Controlling Recorders and Sequencers Remotely from the GS-10 (Remote Control)

76Chapter 8 Using the GS-10 with External MIDI Devices ConnectedControlling the Device RemotelyMaking the ConnectionsMake the connections as shown bel

77Chapter 8 Using the GS-10 with External MIDI Devices ConnectedSection 8Settings Example: When Using SONAR 2.0The following settings allow you to con

78Chapter 9 Using the GS-10 Connected to a Computer Via USBBefore Connecting with USBWith the GS-10, you can use USB to transmit both digital audio si

79Chapter 9 Using the GS-10 Connected to a Computer Via USBSection 9Enabling and Disabling the Direct Monitor CommandThis setting determines whether o

8ContentsChapter 9 Using the GS-10 Connected to a Computer Via USB ...78 Before Connecting with USB...78 Dr

80Chapter 9 Using the GS-10 Connected to a Computer Via USBSwitching the Driver ModeAfter first installing both the special and standard drivers and t

81Chapter 9 Using the GS-10 Connected to a Computer Via USBSection 9Recording the GS-10’s Output with a ComputerSet your application (such as a sequen

82AppendicesAbout MIDIMIDI is an acronym for Musical Instrument Digital Interface, and is a world-wide standard for allowing electronic musical equipm

83AppendicesAppendicesAbout the MIDI implementationMIDI allows a variety of messages to be exchanged between instruments, but it is not necessarily th

84AppendicesPatch ListNo. Patch Name OD/DSCh. Selectch-A ch-B ch-CP101 POWER LEAD - A MS1959(I) Drive Stack Metal LeadP102 WARM CLEAN

85AppendicesAppendices* With the factory settings, the content of the User patches is the same as that of the Preset patches.* Patches with [Mic] appe

86AppendicesRestoring the Factory Settings (Factory Reset)Restoring the GS-10 to the settings made at the factory is referred to as “Factory Reset.”No

87AppendicesAppendicesRoland Exclusive Messages1. Data Format for Exclusive Messages Roland’s MIDI implementation uses the following data format for

88Appendices* The size of the requested data does not indicate the number of bytes that will make up a DT1 message, but represents the address fields

89AppendicesAppendicesMIDI ImplementationModel: GS-10Date: Jul. 15, 2003Version: 1.001. RECOGNIZED RECEIVE DATA CHANNEL VOICE MESSAGE●Control ChangeSt

9 Main Features True “Tabletop Guitar Effects System” This is an all-new guitar effects system, which gives you not only the kind of professional-qua

90Appendices●MIDI Machine Control (MMC)F0H 7FH 7FH 06H com F7HF0H = System Exclusive7FH = ID Number (Universal Realtime Message)7FH = Device ID (Broad

91AppendicesAppendicesAddress Block Map----------------------------------------------------------------------------------------Address Block

92AppendicesPatch Change When transmitted: Transmits the patch number. DATA: Patch NumberWhen received: Changes the Patch.

93AppendicesAppendicesTable DIRECT PATCH <SYSTEM: DIRECT PATCH>----------------------------------------------------------------------------

94AppendicesTable MIDI <SYSTEM: MIDI>----------------------------------------------------------------------------------------------

95AppendicesAppendicesTable HARMONIST <HARMONIST User Scale>----------------------------------------------------------------------------

96Appendices--- Scale 9 ---03 00 08 00 00 00 00 01 00 - 30 Scale 9 C *Refer to "Table HR Harmony Note"03 00 08 01

97AppendicesAppendices--- Scale 18 ---03 00 11 00 00 00 00 01 00 - 30 Scale 18 C *Refer to "Table HR Harmony Note"03 00

98Appendices--- Scale 27 ---03 00 1A 00 00 00 00 01 00 - 30 Scale 27 C *Refer to "Table HR Harmony Note"03 00 1A 01

99AppendicesAppendicesTable AUTO RIFF <AUTO RIFF User Phrase>---------------------------------------------------------------------------